Less Carb & Ignition
454 - Isn't That A Big Block? That's What Everyone Will Say When You Tell Them That You Have One Of These! Our 454 Is Not Just A 434 Bored Out To A Ridiculous "Paper Thin" Size. It's A Real Race Engine With A Tall Deck Block, Raised Billet Cam, Steel Billet Caps & The Best Components That You Can Get. Just What You Would Need For A Reliable 454 Race Engine!!
- Cubic Inch
- Bore & Stroke
- Horsepower
- Torque
- 454
- 4.185 x 4.125
- 760 @ 6600 RPM
- 655 @ 5700 RPM
- Dart Iron Eagle Raised Cam Block w/Splayed Billet Caps
- Eagle 4340 4.125" Stroke Steel Crank
- Eagle 4340 6.200" H-Beam 3D Steel Rods
- Clevite 77 "H" Series Main & Rod Bearings
- JE 14.5 Pro Series Forged Pistons
- Total Seal Plasma Moly Ring Package
- SSRE Custom Grind 7/4 Swap Steel Billet Roller Cam
- Comp Cams Heavy Duty Solid Roller Lifters
- Cloyes Billet True Roller Timing Set w/Torrington Bearing
- New Brodix 233 Fully CNC Ported Aluminum Heads
- 1.550" Roller Springs w/Titanium Retainers & 10° Locks
- ARP Head Studs w/12-Point Nuts
- Harland Sharp 1.6 Aluminum Roller Rockers
- FelPro HP Head Gaskets w/Pre-Flattened Copper Wire
- Dart Tall Deck SuperMod Ported Dominator Intake Manifold
- SSRE/Moroso Wide Rail Stroker Oil Pan w/Baffling
- Moroso Race Prepped Oil Pump w/Tig-Welded HD Pickup
- Polished Aluminum Front Cover w/Billet Pointer
- SFI Approved Harmonic Balancer
- Complete Assembly Internally Balanced
- Individually Dyno Tested & Tuned
- Actual Dyno Sheet Provided
 |
|
|
| Fuel System Components: | ||
| Why Buy A Carburetor From Us? Yes, you can certainly purchase a stock carb from the big mail order companies but we've seen carbs out of the box down on power as much as 40HP and between 15-20HP is common. That's why we disassemble and blueprint EVERY carburetor before we ever bolt it on your engine. We then tune, adjust and jet your carb on your engine so you get every once of power that you paid for. Even if you're considering one of our Engine Kits or simply looking for a replacement carb, the same blueprint work is done and we dyno test it on a comparable engine to yours before it ships! |
|
$ Priceless |
| 1050 CFM Holley Dominator Carb Package includes: Carb, Phenolic Spacer, Aluminum AN Fuel Fittings, Studs & Gaskets. Dyno Tuned, Jetted and Calibrated on your engine. | |
$ 995 |
| QuickFuel 950 CFM Carb Package includes: Carb w/Billet Metering Blocks & Throttle Body, Phenolic Spacer, Aluminum AN Fuel Fittings, Studs & Gaskets. Dyno Tuned, Jetted and Calibrated on your engine. Includes Edelbrock Super Victor Intake. | |
$ 895 |
MagnaFuel ProStar 500 Billet Gerotor Electric Fuel Pump |
|
$ 399 |
| Ignition Components: | ||
| MSD Electronic Ignition Package includes MSD Pro Billet Locked Distributor w/Ford HEI-Style Cap, Bronze Gear, Custom MSD 8.5mm Wire Set. Dyno Tested and Calibrated on your engine. | |
$ 395 |
| MSD Crank Trigger Ignition Upgrade | |
$ 275 |
| MSD 7AL-2 Electronic Ignition Box (Direct Plug-in For Our MSD Distributors) | |
$ 559 |
| MSD 8201 Pro Power Coil | |
$ 116 |
| Short Block Components: | ||
| Brodix Aluminum Block w/Special Head Stud Kit & Additional Machining (Slightly Less Peak HP) |
|
$ 4000 |
| Callies USA Made 4340 Magnum Plus Pro Series Crank | |
$ 995 |
| Eagle 4340 3D Rods w/ARP 2000 Rod Bolts | |
$ 125 |
| Oliver Steel Billet Rods | |
$ 895 |
| Callies CompStar Pro Series I-Beam Rods | |
$ 495 |
| Cometic MLS (Multi Layered Steel) Head Gaskets | |
$ 95 |
| Calico Coated Bearing Package (Cam, Rods & Mains) | |
$ 150 |
| ATI SFI Approved Super Damper Balancer | |
$ 225 |
| Pistons/Pins/Rings: | ||
| Hellfire® Rings | |
$ 175 |
| Tool Steel "Heavy Wall" Wrist Pins | |
$ 200 |
| Valvetrain/Timing Components: | ||
| HIPPO Pro Series Roller Lifters w/Hi-Pressure Pin Oiling (Extended Lifter Life) | |
$ 295 |
| Isky Red Zone Roller Lifters w/EZX "Needle Free" Bearing Option | |
$ 595 |
| SSRE Stud Girdle w/CNC Machined 2-Piece Valvetrain Stabilizer & Locking Hex Head Adjusting Nuts | |
$ 250 |
| Jesel Shaft Rocker System (Includes Labor For Mandatory Head Machining & Special Valve Covers) | |
$ 1125 |
| Jesel .391" Raised Cam Belt Drive (Includes $175 Labor Change For Mandatory Block Machining) | |
$ 1525 |
| Intake Manifolds/Nitrous Systems: | ||
| SpeedTech Diffuser Plate Nitrous System - Installed | |
$ 730 |
| SpeedTech Liquid Force "Fogger Style" Nitrous System - Plumbed & Installed | |
$ 1500 |
| Oil Pumps/Vacuum Pumps: | ||
Moroso HD Billet Aluminum Oil Pump |
|
$ 295 |
| Moroso Vacuum Pump Kit w/Adjustable Relief Valve (Installed) | |
$ 975 |
| Remote Oil Filter Mounting Kit includes: Filter Mount, AN Fittings and -12 Braided Line. | |
$ 250 |
| Accessories: | ||
Meziere 55GPH Electric Water Pump |
|
$ 375 |
PowerMaster Hi-Torque Mini Starter |
|
$ 229 |
| SFI Heavy Duty Flex Plate & ARP Bolt Package | |
$ 125 |
JW "The Wheel" Severe Duty SFI Flex Plate |
|
$ 200 |
Meziere "Ten Pitch" 2.2KW Starter w/Super Duty Drive (Requires FPT300 "Ten Pitch" Flexplate) |
|
$ 525 |
Meziere "Ten Pitch" True Billet 139 Tooth SFI Flexplate (Requires TST400 "Ten Pitch" Starter) |
|
$ 357 |
| PowerMaster XS Power AGM 16 Volt Battery (Only 33 lbs!) | |
$ 249 |
| PowerMaster PWM-1005 16 Volt Battery Charger | |
$ 299 |
Custom Locking & Calibrated Dipstick |
|
$ 95 |
Components Subject To Change Due To Availability.
Free Freight Applies To All Advertised Items Shipped To A Commercial Address In The 48 States. Residential, Out-Of-Area Or Lift Gate Service Subject To Additional Charges. Insurance & Handling Fees Apply.
Toll Free: 800.295.7142 • Phone: 631.218.7530 • FAX: 631.218.7540 • Email: ssre123@aol.com
35 Davinci Drive • Bohemia, NY 11716
HOURS: Mon - Thu 9:00 a.m. - 6:00 p.m. Friday 9:00 a.m. - 3:00 p.m. EST
A Division Of Scott Shafiroff Race Engines & Components © 2000-2011 All Rights Reserved