540 Big Block Chevy Ultrastreet Pump Gas Engine
Pump Gas

540 Big Block Chevy Ultrastreet Pump Gas Engine $15,150

540/715HP $15,150
Less Carb & Ignition

This Engine Provides Both The Power And The Sound That Screams "Hot Rod". Utilizing A Mild "Street Roller" Cam Profile And A 10.5 Compression Ratio, It Delivers The Tire Melting Power You Want And The Cruising Reliability You Need In A Pump Gas Friendly Package.

  • Horsepower
  • Torque
  • Bore & Stroke
  • Compression Ratio
  • Fuel Requirement
  • 715 @ 6200 RPM
  • 665 @ 4500 RPM
  • 4.500 x 4.250
  • 10.5 to 1
  • 92 Octane

New Brodix Low Profile Intake!
  • Dart Big "M" 9.8" Block w/Splayed 4 Bolt Main Caps
  • SSRE/Scat 4340 4.250" Stroke Steel Crank (1)
  • Scat 4340 6.385" H-Beam Steel Rods
  • Clevite 77 "H" Series Main & Rod Bearings
  • JE/SRP 10.5-1 Forged Aluminum Pistons w/Coated Skirts
  • Plasma Moly Ring Set
  • SSRE/Comp Cams Custom "Street Roller" Camshaft (2)
  • Comp Cams Solid Roller Lifters
  • Rollmaster Billet Timing Set w/IWIS Chain & Torrington Bearing
  • Dart Pro 1 325 Aluminum Heads
  • 1.550" Roller Springs w/Steel Retainers
  • ARP High Performance Head Bolts
  • Comp Cams 1.7 Ultra Pro Magnum Roller Rockers
  • Chromemoly (1) Piece .080" Wall Pushrods
  • FelPro HP Head Gaskets w/Pre-Flattened Steel Wire
  • BMP Merlin "X" Dominator Aluminum Intake (3)
  • SSRE/Moroso Street/Strip Oil Pan w/Windage Tray
  • Moroso Race Prepped Oil Pump w/Tig Welded HD Pickup
  • GM Performance Chrome Front Cover w/Billet Timing Pointer
  • Hi-Performance Harmonic Balancer
  • Complete Assembly Internally Balanced
  • Individually Dyno Tested & Tuned
  • Actual Dyno Sheet Provided
  • Footnotes:
  • (1) Precision machined in USA to our custom specifications.
  • (2) Composite Fuel Pump Rod Required with our custom camshafts.
  • (3) 4150 Style Carb Available.
Holley Sniper EFI Package$2495
Includes: Holley Super Sniper EFI Unit, Sniper EFI Touchscreen LCD Programmer, Bosch LSU 4.9 Wideband Oxygen Sensor, Stainless Steel Clamp-On Oxygen Sensor Installation Kit (May Also Be Welded), Hyperspark Distributor and SSRE Custom Ignition Wires w/Looms. Base Tuneup and Parameters Set and Calibrated on Your Engine.
Igniton Components
Hyperspark Ignition Coil $39
E85 Version $295

If This Fuel Is Readily Available In Your Area, Our E85 Version Offers Much Greater HP And Torque Numbers Over Its' Gasoline Equivalent. E85 Fuel's Ability To Operate Without Detonation Under Much Higher Cylinder Pressure Allows Us To Significantly Raise The Compression Ratio And Slightly Alter Cam Timing To Produce These Dramatic Improvements. You Must Run An E85 Specific Carb Or Program Your Aftermarket Fuel Injection To Work With This Engine.

"HHR" Hot Hydraulic Roller $995

For Those That Want Even More Power Than "The Classic" Without The Hassle Of Ever Having To Adjust Valves, The HHR Is For You! We Use Special "Proprietary Grinds" On Our Custom Hot Hydraulic Roller Cam Along With "Ultra Hi-Rev" Hydraulic Roller Lifters. This Version Also Comes Standard w/CNC Ported Combustion Chambers And Premium Alloy Valve Springs To Maintain Race Engine Performance With Hydraulic Roller Convenience.

  • Dart 325cc Aluminum Heads w/CNC Ported Chambers
  • Comp Cams Custom "Proprietary Grind" Hydraulic Roller Cam
  • High Rev Hydraulic Roller Lifters
  • Isky "Enduro Design" Premium Valve Spring Package
  • Horsepower
  • Torque
  • Compression Ratio
  • Fuel Requirement
  • 730 @ 6000 RPM
  • 690 @ 4500 RPM
  • 10.5 to 1
  • 92 Octane
"SS" Saturday Night Special $1,995

The "Saturday Night Special" Package Is Designed For The Hot Rodder That Puts Performance Above All Else. It Combines "Limited" Streetability With "Race Engine" Performance In A Pump Gas Version! This Is The "Bad Boy" Of The Bunch! Putting Out Almost 800HP, This Monster Requires Competition Drive Train, Chassis And Exhaust Mods To Deliver Its Maximum Potential. With Its slightly Higher Compression, More Aggressive Cam And Fully CNC Ported 335cc Dart Pro 1 Aluminum Heads, It Requires A Minimum Of 93 Octane Gas, But That's A Small Price To Pay For The Incredible Performance This Package Delivers.

  • Dart Pro 1 Fully CNC Ported 335cc Aluminum Heads
  • Manley 1.640" NexTek Roller Springs
  • Titanium Retainers w/10° Locks
  • Scorpion Race Series 1.7 Aluminum Roller Rockers
  • ARP Competition Head Stud Kit
  • JE/SRP Custom Coated 10.75-1 Forged Aluminum Pistons
  • Comp Cams Custom Ground Steel Billet Solid Roller Cam
  • Stage I Merlin X Dominator Intake
  • Horsepower
  • Torque
  • Compression Ratio
  • Fuel Requirement
  • 795 @ 6300 RPM
  • 690 @ 4800 RPM
  • 10.75 to 1
  • 93 Octane




Nitrous Package $890

Planning On Adding Nitrous? We've Put Together A Preferred Option Package Of Our Most Popular And Highly Recommended Heavy Duty Components ... With The Added Bonus Of Savings!!


●  Manley 4340 Non-Twist Forged & Nitrided Crank $150
●  Manley H-Beam 4340 Steel Rods w/ARP 2000 Bolts $300
●  Calico Coated Bearing Package $150
●  Total Seal TNT "Hellfire" Rings $175
●  Cometic MLS (Multi Layered Steel) Head Gaskets $125
●  Dart Inner Valley Stud Kit (Improved Head Gasket Sealing) $95

Total Package Value = $995 - Save $105!

Fuel System Components
Why Buy A Carburetor From Us?

Yes, you can certainly purchase a stock carb from the big mail order companies but we've seen carbs out of the box down on power as much as 40HP and between 15-20HP is common. That's why we disassemble and blueprint EVERY carburetor before we ever bolt it on your engine. We then tune, adjust and jet your carb on your engine so you get every ounce of power that you paid for.

Even if you're considering one of our Engine Kits or simply looking for a replacement carb, the same blueprint work is done and we dyno test it on a comparable engine to yours before it ships!
 $Priceless
APD 950 CFM 4150 Series Carb Package includes: 2 Circuit Billet Carb, Phenolic Spacer, Aluminum AN Fuel Fittings, Studs & Gaskets. Dyno Tuned, Jetted and Calibrated on your engine.Image Close$995
APD 1040 CFM 4150 Series Carb Package includes: 2 Circuit Billet Carb, Phenolic Spacer, Aluminum AN Fuel Fittings, Studs & Gaskets. Dyno Tuned, Jetted and Calibrated on your engine.Image Close$995
APD 1050 CFM 4500 Series E85 Carb Package includes: 2 Circuit Billet Carb, Phenolic Spacer, Aluminum AN Fuel Fittings, Studs & Gaskets. Dyno Tuned, Jetted and Calibrated on your engine.Image Close$1495
APD 1050 CFM 4500 Series Carb Package includes: 2 Circuit Billet Carb, Phenolic Spacer, Aluminum AN Fuel Fittings, Studs & Gaskets. Dyno Tuned, Jetted and Calibrated on your engine.Image Close$1395
Mechanical Fuel Pump Package Includes: High Volume Race Design 6 Valve Pump, Composite Fuel Pump Rod (Required For Our Custom Cams), Braided Fuel Line Inlet Kit w/8AN Lines and Fittings. Plumbed, Installed & Dyno Tested On Your Engine. $475
Igniton Components
MSD Electronic Ignition Package Includes: MSD Pro Billet Distributor, Hi Perf Gear, Custom Moroso 8mm Wire Set. Custom Curved and Calibrated To Your Engine. $595
MSD 6AL Digital Electronic Ignition Box w/Hi-Speed Rev Limiter $305
MSD 6AL-2 Digital Electronic Ignition Box w/Launch Control & Hi-Speed Rev Limiter $480
MSD Blaster 3 Hi Performance Ignition Coil w/HEI Style Post $65
MSD 8201 Pro Power Coil $159
Composite Distributor Gear (if required)Image Close$125
Blocks
Machine Block and Install Lifter Valley Screen Kit $95
Dart Inner Valley Stud Kit (Improved Head Gasket Sealing) $95
Brodix Aluminum Block w/Steel Billet Caps, Special Head Stud Kit & Additional Machining (Slightly Less Peak HP) $4500
HIP® Process (Hot Isostatic Pressing) For Increased Durability With Aluminum Blocks $675
Crankshafts
Manley 4340 Non-Twist Forged & Nitrided Crank $150
Connecting Rods
ARP 2000 Rod Bolts $125
Manley H-Beam 4340 Steel Rods w/ARP 2000 Bolts $300
Pistons - Pins - Rings - Bearings
Severe Duty JE Pistons (Suitable For Over 250HP Nitrous) $295
Total Seal TNT "Hellfire" Rings $175
Calico Coated Bearing Package $150
Lifters
HIPPO Severe Duty Roller Lifters w/Hi-Pressure Pin Oiling (Extended Lifter Life) $295
Morel "Black Mamba" Needleless Roller Lifters $695
Valvetrain
T&D Shaft Rocker System Available In 1.70, 1.75 or 1.80 Ratio (Split Ratio Sets No Extra Charge) $1795
Crower Stainless Steel Shaft Rocker Arm System. Designed For Severe Duty Street Use.Image Close$1995
Timing
Cloyes 2 Piece Aluminum Timing CoverImage Close$195
Jesel "Original 2 pc" Belt Drive $1145
Oil Pumps - Oil Pans - Vacuum Pump
Lokar Custom Locking & Calibrated Dipstick (Upgrade)Image Close$95
Moroso Kickout Style Pro Pan w/Solid Louvered Tray & Main Cap Partitions For Added Power & Oil Control. (Includes New Wing Design Oil Pump) $395
Vacuum Pump Kit Includes: Moroso 3 Vane Vacuum Pump & Adjustable Relief Valve, Breather Tank, AN Fittings, Jones Mandrel & Bracket Kit w/Radius Tooth HTD Belt. Image Close$1395
Additional Parts - Labor - Accessories
Cometic MLS (Multi Layered Steel) Head Gaskets $125
SFI Approved Harmonic Balancer (Required At All Race Tracks) $150
ATI SFI Approved Super Damper Balancer (Includes Hone To Fit Labor) $295
Master Power Silent Drive Vacuum Pump Kit For Power BrakesImage Close$589
SFI Heavy Duty Flexplate & ARP Bolt Package $150
Boninfante Severe Duty SFI Flexplate & ARP Bolt PackageImage Close$229
Boninfante SFI Billet Flexplate & ARP Bolt PackageImage Close$395
PowerMaster Hi-Torque Mini StarterImage Close$229
Painless Performance Hot Shot Relay Kit (Recommended for above starter) $39
Edelbrock Aluminum "High Volume" Mechanical Water Pump (Short or Long Version)Image Close$350
Meziere 55GPH Electric Water PumpImage Close$535
Billet Specialties Tru Trac Serpentine SystemImage Close$Call
Billet Specialties V-Track Pulley SystemImage Close$Call
Custom Powder Coating Packages Available $Call
SSRE Engraved Sheet Metal Valve Covers w/BreathersImage Close$375
Show Quality Polished Chrome Plated Finish For Sheet Metal Valve Covers (Additional Charge)Image Close$Call